[nycbug-talk] g4u on proliant 360 g4 scsi raid 1

Tue Jun 7 13:30:25 EDT 2005

On 6/7/05, Steve Rieger <steve.rieger at tbwachiat.com> wrote:
> hi all
> need a favor
> 
> i have 14 proliant 360's that i want to clone, but g4u that i am
> pulling off the site does not pick up the raid array (raid 1) and since
> i do not have netbsd running am wondering if any of you compiled g4u
> with all the bells and whistles instead of the stripped down version
> that i have.
> 

Hey Steve,
     While this is not a BSD specific solution, but we have been using
UDPcast over here to clone machines.  I boot's a 2.6 linux kernel and
seems to have a wide array of drivers installed.  I am trying to
remember if this is the utility that basicly stole the source from
G4U.  ..although I don't believe it is.

In anyevent we are able to get very good performace out of this via
gig-e and LZOP compression.

http://udpcast.linux.lu/

-pete

> 
> here is my hw stuff (dmesg)
> 
> 
> thanx
> 
> 
> 
> Copyright (c) 1992-2005 The FreeBSD Project.
> Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
>         The Regents of the University of California. All rights reserved.
> FreeBSD 5.4-STABLE #0: Thu Jun  2 11:33:53 EDT 2005
>      /usr/obj/usr/src/sys/custom-smp
> Timecounter "i8254" frequency 1193182 Hz quality 0
> CPU: Intel(R) Xeon(TM) CPU 3.40GHz (3400.14-MHz 686-class CPU)
>    Origin = "GenuineIntel"  Id = 0xf41  Stepping = 1
> 
> Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE
> ,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
>    Hyperthreading: 2 logical CPUs
> real memory  = 3758043136 (3583 MB)
> avail memory = 3678244864 (3507 MB)
> ACPI APIC Table: <HP     00000083>
> FreeBSD/SMP: Multiprocessor System Detected: 4 CPUs
>   cpu0 (BSP): APIC ID:  0
>   cpu1 (AP): APIC ID:  1
>   cpu2 (AP): APIC ID:  6
>   cpu3 (AP): APIC ID:  7
> ioapic1: Changing APIC ID to 9
> ioapic0 <Version 2.0> irqs 0-23 on motherboard
> ioapic1 <Version 2.0> irqs 24-47 on motherboard
> ioapic2 <Version 2.0> irqs 48-71 on motherboard
> ioapic3 <Version 2.0> irqs 72-95 on motherboard
> npx0: <math processor> on motherboard
> npx0: INT 16 interface
> acpi0: <HP P52> on motherboard
> acpi0: Power Button (fixed)
> Timecounter "ACPI-safe" frequency 3579545 Hz quality 1000
> acpi_timer0: <24-bit timer at 3.579545MHz> port 0x908-0x90b on acpi0
> cpu0: <ACPI CPU> on acpi0
> cpu1: <ACPI CPU> on acpi0
> cpu2: <ACPI CPU> on acpi0
> cpu3: <ACPI CPU> on acpi0
> pcib0: <ACPI Host-PCI bridge> on acpi0
> pci0: <ACPI PCI bus> on pcib0
> pcib1: <ACPI PCI-PCI bridge> at device 2.0 on pci0
> pci13: <ACPI PCI bus> on pcib1
> pcib2: <ACPI PCI-PCI bridge> at device 4.0 on pci0
> pci6: <ACPI PCI bus> on pcib2
> pcib3: <ACPI PCI-PCI bridge> at device 0.0 on pci6
> pci7: <ACPI PCI bus> on pcib3
> pcib4: <ACPI PCI-PCI bridge> at device 0.2 on pci6
> pci10: <ACPI PCI bus> on pcib4
> pcib5: <ACPI PCI-PCI bridge> at device 6.0 on pci0
> pci3: <ACPI PCI bus> on pcib5
> pcib6: <ACPI PCI-PCI bridge> at device 28.0 on pci0
> pci2: <ACPI PCI bus> on pcib6
> ciss0: <HP Smart Array 6i> port 0x4000-0x40ff mem
> 0xfdf80000-0xfdfbffff,0xfdff0000-0xfdff1fff irq 24 at device 1.0 on
> pci2
> bge0: <Broadcom BCM5704C Dual Gigabit Ethernet, ASIC rev. 0x2100> mem
> 0xfdf70000-0xfdf7ffff irq 25 at device 2.0 on pci2
> miibus0: <MII bus> on bge0
> brgphy0: <BCM5704 10/100/1000baseTX PHY> on miibus0
> brgphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseTX,
> 1000baseTX-FDX, auto
> bge0: Ethernet address: 00:13:21:b1:7a:24
> bge1: <Broadcom BCM5704C Dual Gigabit Ethernet, ASIC rev. 0x2100> mem
> 0xfdf60000-0xfdf6ffff irq 26 at device 2.1 on pci2
> miibus1: <MII bus> on bge1
> brgphy1: <BCM5704 10/100/1000baseTX PHY> on miibus1
> brgphy1:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseTX,
> 1000baseTX-FDX, auto
> bge1: Ethernet address: 00:13:21:b1:7a:23
> uhci0: <UHCI (generic) USB controller> port 0x2000-0x201f irq 16 at
> device 29.0 on pci0
> usb0: <UHCI (generic) USB controller> on uhci0
> usb0: USB revision 1.0
> uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
> uhub0: 2 ports with 2 removable, self powered
> uhci1: <UHCI (generic) USB controller> port 0x2020-0x203f irq 19 at
> device 29.1 on pci0
> usb1: <UHCI (generic) USB controller> on uhci1
> usb1: USB revision 1.0
> uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
> uhub1: 2 ports with 2 removable, self powered
> pci0: <base peripheral> at device 29.4 (no driver attached)
> pci0: <base peripheral, interrupt controller> at device 29.5 (no driver
> attached)
> pci0: <serial bus, USB> at device 29.7 (no driver attached)
> pcib7: <ACPI PCI-PCI bridge> at device 30.0 on pci0
> pci1: <ACPI PCI bus> on pcib7
> pci1: <display, VGA> at device 3.0 (no driver attached)
> pci1: <base peripheral> at device 4.0 (no driver attached)
> pci1: <base peripheral> at device 4.2 (no driver attached)
> isab0: <PCI-ISA bridge> at device 31.0 on pci0
> isa0: <ISA bus> on isab0
> atapci0: <Intel 6300ESB UDMA100 controller> port
> 0x500-0x50f,0x376,0x170-0x177,0x3f6,0x1f0-0x1f7 irq 18 at device 31.1
> on pci0
> ata0: channel #0 on atapci0
> ata1: channel #1 on atapci0
> acpi_tz0: <Thermal Zone> on acpi0
> atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on acpi0
> atkbd0: <AT Keyboard> irq 1 on atkbdc0
> kbd0 at atkbd0
> psm0: <PS/2 Mouse> irq 12 on atkbdc0
> psm0: model IntelliMouse Explorer, device ID 4
> sio0: <Standard PC COM port> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
> sio0: type 16550A
> fdc0: <floppy drive controller (FDE)> port 0x3f2-0x3f5 irq 6 drq 2 on
> acpi0
> fd0: <1440-KB 3.5" drive> on fdc0 drive 0
> orm0: <ISA Option ROMs> at iomem
> 0xee000-0xeffff,0xcc000-0xcd7ff,0xc8000-0xcbfff,0xc0000-0xc7fff on isa0
> pmtimer0 on isa0
> ppc0: parallel port not found.
> sc0: <System console> at flags 0x100 on isa0
> sc0: VGA <16 virtual consoles, flags=0x300>
> sio1 at port 0x2f8-0x2ff irq 3 on isa0
> sio1: type 16550A
> vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on
> isa0
> Timecounters tick every 10.000 msec
> acd0: CDROM <CRN-8245B/2.19> at ata0-master PIO4
> da0 at ciss0 bus 0 target 0 lun 0
> da0: <COMPAQ RAID 1  VOLUME OK> Fixed Direct Access SCSI-0 device
> da0: 135.168MB/s transfers
> da0: 69459MB (142253280 512 byte sectors: 255H 32S/T 17433C)
> SMP: AP CPU #1 Launched!
> SMP: AP CPU #3 Launched!
> SMP: AP CPU #2 Launched!
> Mounting root from ufs:/dev/da0s1a
> Accounting enabled
> 
> --
> Steve Rieger
> (212) 804-1131   (Work)
> (646) 335-8915   (Cell)
> chozrim           (aim)
> 
> _______________________________________________
> % NYC*BUG talk mailing list
> http://lists.nycbug.org/mailman/listinfo/talk
> %Be sure to check out our Jobs and NYCBUG-announce lists
> %We meet the first Wednesday of the month
> 

-- 
~~o0OO0o~~
Pete Wright
www.nycbug.org
NYC's *BSD User Group